光眼問題.謝謝了!
全部回復(9)
正序查看
倒序查看
@gogo991
是我畫的不好么?還是有不對的地方呢!?
HI!Boy, i believe u rush into a completely wrong place.
the bbs is just for power.
optical-eye is preserved patent of Logictech.
the producer said it's used high speed CCD tech. inside.
but i belive it incorporated with coherent optical tech.
u choice a good target,but i can't give u more comment,sorry.
the bbs is just for power.
optical-eye is preserved patent of Logictech.
the producer said it's used high speed CCD tech. inside.
but i belive it incorporated with coherent optical tech.
u choice a good target,but i can't give u more comment,sorry.
0
回復
@小學生
HI!Boy,ibelieveurushintoacompletelywrongplace.thebbsisjustforpower.optical-eyeispreservedpatentofLogictech.theproducersaidit'susedhighspeedCCDtech.inside.butibeliveitincorporated withcoherentopticaltech.uchoiceagoodtarget,butican'tgiveumorecomment,sorry.
hi !young boy,please translate these sentences into chinese,because none understand what you said ,there was 5 errors in your sentences.can't you find them?by the way ,what do you do? a student? a teacher?
0
回復
@ghost
有性格我欣賞!雖然你的圖不對可大概意思我明白.要改的地方你可從描述中查覺.R4為發光二極管D2限流電阻,D1為光敏電阻信號經T1放大(R5為D1偏置電阻,R1R2為T1偏置電阻使放大電路能正常工作)后由集電極輸出經NO到COIN遮光時能改變輸出狀態,而T2R3提供一個低電位經集電極輸出到NC端通過撥位開關的控制可使電路工作在手動或遮光控制方示,不知分析的和作者本意有何差別?
帥哥.
你的話上半部分小弟基本理解.
這個電路圖主要是用于計數的.
當NC與中間的點短路時.我們視為"常連"COIN與地線視為短路處理.當有一物體在二只發光二極管中間穿過時.計數器計一數
當NO與中間點短路時.我們視為"常開"COIN與地線視為開短處理.當有一物體在二只發光二極管中間穿過時.計數器計一數
NC與NO只是視二種機器型號而用到不同的常連與常開.
再次想問一下.R5為何種偏置電阻?
你的話上半部分小弟基本理解.
這個電路圖主要是用于計數的.
當NC與中間的點短路時.我們視為"常連"COIN與地線視為短路處理.當有一物體在二只發光二極管中間穿過時.計數器計一數
當NO與中間點短路時.我們視為"常開"COIN與地線視為開短處理.當有一物體在二只發光二極管中間穿過時.計數器計一數
NC與NO只是視二種機器型號而用到不同的常連與常開.
再次想問一下.R5為何種偏置電阻?
0
回復
@gogo991
帥哥.你的話上半部分小弟基本理解.這個電路圖主要是用于計數的.當NC與中間的點短路時.我們視為"常連"COIN與地線視為短路處理.當有一物體在二只發光二極管中間穿過時.計數器計一數當NO與中間點短路時.我們視為"常開"COIN與地線視為開短處理.當有一物體在二只發光二極管中間穿過時.計數器計一數NC與NO只是視二種機器型號而用到不同的常連與常開.再次想問一下.R5為何種偏置電阻?
這就對了嗎,你想想沒有R5,D1怎能輸出高低電平?
0
回復
